5.3 Listing the System Configuration

This section describes how to determine your system configuration group.

The factory System Load Tape (SLT) does not contain a default I/O configuration. During an installation, you must specify the appropriate factory configuration group when booting the system immediately after installing the factory SLT. Listing the system configuration uses the off-line diagnostic tool, Mapper. To get help using MAPPER, type help at the MAPPER prompt, and see Figure 5-1 “Sample Listing MAPPER Output” for a sample listing.

To list the system configuration:

Check that all hardware peripherals are attached and powered on.
Start ODE.
ISL>ODE
Display hardware configuration.
ODE>RUN MAPPER
ODE>RUN MAPPER2 (for N-Class and A-Class systems)
The figure on the following page is a sample of a MAPPER display.
Record the I/O configuration for your system.
Find the MPE/XL Model String. Then refer to Appendix B “Configuration Tables” for the configuration group name for your HP e3000 model in the SCSI column. For example, for a Model 995, the SCSI group is CONFG995. It is very important to have the exact group name. Check carefully for numbers zero and 1 and letters O and I.

Exit mapper.

ODE>EXIT

Figure 5-1 Sample Listing MAPPER Output

STARTING EXECUTION OF MAPPERProcessor Identification:    Hardware Model:  590H, Revision: 0
    Software Model:  4H, Revision:  0
    Hardware ID:  0, Software ID:  250911381 (unsigned decimal)
    Software Cap:  0x10000031
    MPE/XL Model String: 979-400
    Processor Board Revisions:
        CPU - CPU Chip:                   769
        PDC - Processor Dependent Code:   38.29
    Cache and TLB Sizes:
        Instruction Cache:  1024 K bytes, Instruction TLB:  96 entries
        Data Cache:         1024 K bytes, Data TLB:         96 entries
    Co-processors:
        Floating Point Co-processor is installed
 
I/O Configuration:
                                              Type  HW    SW    Revisions
Path       Component Name                      ID    Mod   Mod   Hdwr  Firm--------- ---------------------------------- ----- ----- ----- ----- -----
8          I/O Adapter                         CH    580H  BH    15    1
8/63       GSC+ Port                           7H    501H  CH    1     3
10         I/O Adapter                         CH    580H  BH    15    1
10/4       Upper Bus Converter                 7H    500H  CH    0     0
10/4/0     HP-PB LAN/Console                   2H    5H    60H   0     1
10/4/4     HP-PB Fast Wide SCSI                4H    4H    3BH   0     0
10/4/4.2.0    SEAGATE ST318275LC               -     -     -     -     HP00
10/4/4.3.0    SEAGATE ST39175LC                -     -     -     -     HP00
10/4/4.4.0    SEAGATE ST39175LC                -     -     -     -     HP00
10/4/8     HP-PB SCSI                          4H    4H    39H   0     0
10/4/8.0.0    SEAGATEST32550N disk drive       -     -     -     -     HP10
10/4/8.1.0    SEAGATE ST34572WC                -     -     -     -     HP01
10/4/8.2.0    SEAGATE ST32272WC                -     -     -     -     HP01
10/4/9     HP-PB Centronics                    5H    4H    3AH   0     0
10/4/20    HP-PB SCSI                          4H    5H    39H   0     0
10/4/20.0.0    HPC1533A/C1530B tape drive      -     -     -     -     AN04
10/4/20.1.0    HPC1533A/C1530B tape drive      -     -     -     -     AN04
10/4/24    HP-PB Fast Wide SCSI                4H    5H    3BH   0     0
10/4/24.3.0    SEAGATE ST34371W disk drive     -     -     -     -     HPM2
10/4/24.4.0    SEAGATE ST34371W disk drive     -     -     -     -     HPM2
10/4/24.5.0    Quantum XP34361WD               -     -     -     -     HP10
10/4/24.6.0    SEAGATE ST34371W disk drive     -     -     -     -     HPM4
10/4/60    HP-PB Port                          7H    103H  CH    0     0
10/16      Upper Bus Converter                 7H    500H  CH    0     0
10/16/60   HP-PB Port                          7H    103H  CH    0     0
10/63      GSC+ Port                           7H    501H  CH    1     3
32         MoHawk Processor                    0H    590H  4H    0     0
34         MoHawk Processor                    0H    590H  4H    0     0
36         MoHawk Processor                    0H    590H  4H    0     0
38         MoHawk Processor                    0H    590H  4H    0     0
49         Memory (1024 M bytes)               1H    32H   9H    0     0
             Extender 0
                slot 0A/0B   bank  3:  64MB
                             bank  8:  64MB
                slot 1A/1B   bank  7:  64MB
                             bank 12:  64MB
                slot 2A/2B   bank  4:  64MB
                             bank 15:  64MB
                slot 3A/3B   bank  0:  64MB
                             bank 11:  64MB
                slot 4A/4B   bank  5:  64MB
                             bank 14:  64MB
                slot 5A/5B   bank  1:  64MB
                             bank 10:  64MB
                slot 6A/6B   bank  2:  64MB
                             bank  9:  64MB
                slot 7A/7B   bank  6:  64MB
                             bank 13:  64MB
RUN COMPLETED.

Listing the System Configuration completed. Go to the next section on your checklist.

5.3 Listing the System Configuration

Technical documentation

» Table of Contents

» Glossary

» Index