4.6 Creating the CSLT using HPINSTAL

Start HPINSTAL .

:RUN HPINSTAL.INSTALL.SYS

Select the appropriate option. If you select a subsys option, your system software must be on the same release level as the subsys product.

Please enter the number corresponding to the
software you 
want to install.

1 Update this system
2 
Update this system and ins						tall patches from a PowerPatch tape
3 
Create a CSLT for another system
4 Create a CSLT with PowerPatch 
patches for another system
5 Complete the update of this 
system using a CSLT created on
  another system
6 
Add SUBSYS products to this system
7 Add SUBSYS products 
and install patches from a Powerpatch
  tape
8 
EXIT
? Help on the above actions

Enter 
your choice >>_

Reply to the prompt for the LDEV number. Press [Return] to use the default of device class TAPE, or enter the LDEV number of the device where you want the CSLT to be created. The device you specify applies to all tape requests.

The file equation for the output device (where the CSLT is
created) 
defaults to DEV=TAPE. If you prefer to designate a
specific 
tape device, please enter its LDEV number now (RETURN
for 
default) >>

If you are creating a CSLT on a local system to apply to a Remote system, proceed to Step 5.

If you are performing an Add-on or Update task for a local system only, proceed to Step 6.

Respond to the prompt to specify a Base Group.

If needed, edit or create a PRODLIST.PUB.SYS file.

A master product list was included with the CD-ROM. This list shows all products available to be installed, and needs to be checked against your keyword certificate now.

Respond YES to accept the master list of products at the prompt.

Begin validation of the master product list...
Reading 
PRODLIST.PUB.SYS...
DONE
Your master list contains 
the following 
n
 subsystems:

[The subsystems included in the PRODLIST file are listed here.]

Is the master list of products correct (Y/N)?>

Type or verify the master product keyword at the prompt. Your keyword validates the master product list.

The keyword is included on the keyword certificate that comes with the CD-ROM disks. The keyword is not case sensitive. But you must enter it exactly as it appears including the alphanumerics, slash (/), and hyphen (-).

If you have a keyfile.pub.sys file, hpinstal automatically reads the keyword for your products from the keyfile.pub.sys file. (Refer to Appendix E “CD-ROM Resources” for directions on creating and using the keyfile.pub.sys file.)

Please enter your keyword. The keyword accompanies the CD-ROM. It is made up of fourteen (14) characters including alphanumerics, the slash(/) and the hyphen (-). You must enter your keyword EXACTLY AS IT APPEARS:

Your keyword >>

	NOTE: Add-on product keyword can only be entered interactively.

Select to install all or a portion of the listed products:

Enter Y to select all products on the list.

Enter N to select a subset of the products, proceed to Step 10.

Do you want to install
all of the above products? (Y/N)>>

If you accidentally type N , are viewing the list of products, and you do not wish to make any changes to the list:

Optionally, create a subset list of products from the full list of products.

This is typically done to create a CSLT for use on a remote system, but can be done for your local system as well.

	CAUTION: If you customize the list of products, and if you selected HPINSTAL option 1 or 2, it will create a CSLT with, and install, a subset of the master list of entitled products. If you update your local system with a subset of the master list of products, you cannot use HPINSTAL , option 6 or 7, to add products to the local system.You must use HPINSTAL , option 1 or 2, and customize the subset list of products.

To create a subset list of products:

If you are performing a PowerPatch task, proceed to Step 12.

If you are performing an Add-on or Update task without a PowerPatch, proceed to Step13.

Restore patch information, qualify patches, and restore the patch files.

Create the CSLT.

Mount a write-enabled tape on the appropriate tape drive and reply to the tape request, as prompted. This can take up to two and a half hours.

After the CSLT is created, dismount the tape, label it CSLT v.uu.ff , and set it to read only.

The final response messages vary depending upon the CSLT option you selected. Basically, the response is:

Phase I of HPINSTAL is now complete:

A warning message displays, if applicable.

WARNING -- This program cannot install the products listed below. (INSTWARN #1)

Record on your checklist any products HPINSTAL cannot completely install.

HPINSTAL will automatically cleanup files, exit, and return you to the MPE/iX prompt.

Purging temporary files and cleaning up...

If you are creating a CSLT on a local system to apply to a Remote system, proceed to Step 17.

If you are performing an Add-on or Update task for a local system only, omit Step 17, and go to the next section on your checklist.

Refer to Appendix E “CD-ROM Resources” for directions on creating multiple copies of the CSLT with the SLTCOPY command for use at remote systems.

If you are creating additional modified CSLTs for use on remote systems, reinvoke HPINSTAL and select option 3, "Create a CSLT for another system," for each CSLT you need. If each remote system is unique, you will need to modify the PRODLIST file for each system. Refer to Appendix E “CD-ROM Resources” for directions on creating additional PRODLIST files.