Glossary

This type of multipathed disk array allows you to access a disk in the disk array through all the paths to the disk simultaneously, without any performance degradation.

This type of multipathed disk array allows one path to a disk to be designated as primary and used to access the disk at any time. Using a path other than the designated active path results in severe performance degradation in some disk arrays. Also see path, primary path, and secondary path.

The process of establishing a relationship between VxVM objects; for example, a subdisk that has been created and defined as having a starting point within a plex is referred to as being associated with that plex.

A plex associated with a volume.

A subdisk associated with a plex.

An operation that either succeeds completely or fails and leaves everything as it was before the operation was started. If the operation succeeds, all aspects of the operation take effect at once and the intermediate states of change are invisible. If any aspect of the operation fails, then the operation aborts without leaving partial changes.

In a cluster, an atomic operation takes place either on all nodes or not at all.

A state in which a VxVM object is both associated with another object and enabled for use.

The minimum unit of data transfer to or from a disk or array.

A disk that is used for the purpose of booting a system.

The ability of a node to leave a cluster gracefully when all access to shared volumes has ceased.

A set of hosts (each termed a node) that share a set of disks.

An externally-provided daemon that runs on each node in a cluster. The cluster managers on each node communicate with each other and inform VxVM of changes in cluster membership.

A disk group in which access to the disks is shared by multiple hosts (also referred to as a shared disk group). Also see private disk group.

A set of one or more subdisks within a striped plex. Striping is achieved by allocating data alternately and evenly across the columns within a plex.

A layout style characterized by subdisks that are arranged sequentially and contiguously.

A single copy of a configuration database.

A set of records containing detailed information on existing VxVM objects (such as disk and volume attributes).

A VxVM object that is used to manage information about the FastResync maps in the DCO volume. Both a DCO object and a DCO volume must be associated with a volume to implement Persistent FastResync on that volume.

This represents the usable data portion of a stripe and is equal to the stripe minus the parity region.

A special volume that is used to hold Persistent FastResync change maps.

A state in which a VxVM object is associated with another object, but not enabled for use.

The device name or address used to access a physical disk, such as c0t0d0. The c#t#d# syntax identifies the controller, target address, and disk. In a SAN environment, it is more convenient to use enclosure-based naming, which forms the device name by concatenating the name of the enclosure (such as enc0) with the disk's number within the enclosure, separated by an underscore (for example, enc0_2). The term disk access name can also be used to refer to a device name.

The procedure by which the VxVM monitors and logs modifications to a plex. A bitmap of changed regions is kept in an associated subdisk called a log subdisk.

A path to a disk that is not available for I/O. A path can be disabled due to real hardware failures or if the user has used the vxdmpadm disable command on that controller.

A collection of read/write data blocks that are indexed and can be accessed fairly quickly. Each disk has a universally unique identifier.

An alternative term for a device name.

Configuration records used to specify the access path to particular disks. Each disk access record contains a name, a type, and possibly some type-specific information, which is used by VxVM in deciding how to access and manipulate the disk that is defined by the disk access record.

A collection of disks logically arranged into an object. Arrays tend to provide benefits such as redundancy or improved performance. Also see disk enclosure and JBOD.

This is the serial number of the disk array. It is usually printed on the disk array cabinet or can be obtained by issuing a vendor- specific SCSI command to the disks on the disk array. This number is used by the DMP subsystem to uniquely identify a disk array.

In the multipathing subsystem of VxVM, the controller (host bus adapter or HBA) or disk array connected to the host, which the Operating System represents as the parent node of a disk.

An intelligent disk array that usually has a backplane with a built-in Fibre Channel loop, and which permits hot-swapping of disks.

A collection of disks that share a common configuration. A disk group configuration is a set of records containing detailed information on existing VxVM objects (such as disk and volume attributes) and their relationships. Each disk group has an administrator-assigned name and an internally defined unique ID. The root disk group (rootdg) is a special private disk group that always exists.

A unique identifier used to identify a disk group.

A universally unique identifier that is given to each disk and can be used to identify the disk, even if it is moved.

An alternative term for a disk name.

A configuration record that identifies a particular disk, by disk ID, and gives that disk a logical (or administrative) name.

A logical or administrative name chosen for a disk that is under the control of VxVM, such as disk03. The term disk media name is also used to refer to a disk name.

The process by which any link that exists between two VxVM objects is removed. For example, dissociating a subdisk from a plex removes the subdisk from the plex and adds the subdisk to the free space pool.

A plex dissociated from a volume.

A subdisk dissociated from a plex.

A lock manager that runs on different systems in a cluster, and ensures consistent access to distributed resources.

A path to a disk that is available for I/O.

A process that converts existing partitions on a specified disk to volumes. Encapsulation does not apply to HP-UX.

See disk enclosure.

See device name.

A disk device that is accessible on a Storage Area Network (SAN) via a Fibre Channel switch.

A fast resynchronization feature that is used to perform quick and efficient resynchronization of stale mirrors, and to increase the efficiency of the snapshot mechanism. Also see Persistent FastResync and Non-Persistent FastResync.

A collective name for the fiber optic technology that is commonly used to set up a Storage Area Network (SAN).

A collection of files organized together into a structure. The UNIX file system is a hierarchical structure consisting of directories and files.

An area of a disk under VxVM control that is not allocated to any subdisk or reserved for use by any other VxVM object.

A subdisk that is not associated with any plex and has an empty putil[0] field.

A string that identifies a host to VxVM. The hostid for a host is stored in its volboot file , and is used in defining ownership of disks and disk groups.

A technique of automatically restoring redundancy and access to mirrored and RAID-5 volumes when a disk fails. This is done by relocating the affected subdisks to disks designated as spares and/or free space in the same disk group.

Refers to devices that can be removed from, or inserted into, a system without first turning off the power supply to the system.

The node on which the system administrator is running a utility that requests a change to VxVM objects. This node initiates a volume reconfiguration.

The common name for an unintelligent disk array which may, or may not, support the hot-swapping of disks. The name is derived from "just a bunch of disks."

A plex used to store a RAID-5 log. The term log plex may also be used to refer to a Dirty Region Logging plex.

A subdisk that is used to store a dirty region log.

A node that is designated by the software to coordinate certain VxVM operations in a cluster. Any node is capable of being the master node.

The node to which a disk is attached. This is also known as a disk owner.

A duplicate copy of a volume and the data therein (in the form of an ordered collection of subdisks). Each mirror consists of one plex of the volume with which the mirror is associated.

A layout technique that mirrors the contents of a volume onto multiple plexes. Each plex duplicates the data stored on the volume, but the plexes themselves may have different layouts.

Where there are multiple physical access paths to a disk connected to a system, the disk is called multipathed. Any software residing on the host, (for example, the DMP driver) that hides this fact from the user is said to provide multipathing functionality.

One of the hosts in a cluster.

A situation where a node leaves a cluster (on an emergency basis) without attempting to stop ongoing operations.

The process through which a node joins a cluster and gains access to shared disks.

A form of FastResync that cannot preserve its maps across reboots of the system because it stores its change map in memory.

An entity that is defined to and recognized internally by VxVM. The VxVM objects are: volume, plex, subdisk, disk, and disk group. There are actually two types of disk objects—one for the physical aspect of the disk and the other for the logical aspect.

A calculated value that can be used to reconstruct data after a failure. While data is being written to a RAID-5 volume, parity is also calculated by performing an exclusive OR (XOR) procedure on data. The resulting parity is then written to the volume. If a portion of a RAID-5 volume fails, the data that was on that portion of the failed volume can be recreated from the remaining data and the parity.

A RAID-5 volume storage region that contains parity information. The data contained in the parity stripe unit can be used to help reconstruct regions of a RAID-5 volume that are missing because of I/O or disk failures.

The standard division of a physical disk device, as supported directly by the operating system and disk drives.

When a disk is connected to a host, the path to the disk consists of the HBA (Host Bus Adapter) on the host, the SCSI or fibre cable connector and the controller on the disk or disk array. These components constitute a path to a disk. A failure on any of these results in DMP trying to shift all I/O for that disk onto the remaining (alternate) paths. Also see active/passive disk arrays, primary path and secondary path.

In case of disks which are not multipathed by vxdmp, VxVM will see each path as a disk. In such cases, all paths to the disk can be grouped. This way only one of the paths from the group is made visible to VxVM.

A form of FastResync that can preserve its maps across reboots of the system by storing its change map in a DCO volume on disk. Also see data change object (DCO).

A logging type that ensures that only active mirrors are used for recovery purposes and prevents failed mirrors from being selected for recovery. This is also known as kernel logging.

The underlying storage device, which may or may not be under VxVM control.

A plex is a logical grouping of subdisks that creates an area of disk space independent of physical disk size or other restrictions. Mirroring is set up by creating multiple data plexes for a single volume. Each data plex in a mirrored volume contains an identical copy of the volume data. Plexes may also be created to represent concatenated, striped and RAID-5 volume layouts, and to store volume logs.

In active/passive disk arrays, a disk can be bound to one particular controller on the disk array or owned by a controller. The disk can then be accessed using the path through this particular controller. Also see path and secondary path.

A disk group in which the disks are accessed by only one specific host in a cluster. Also see shared disk group.

A region of a physical disk used to store private, structured VxVM information. The private region contains a disk header, a table of contents, and a configuration database. The table of contents maps the contents of the disk. The disk header contains a disk ID. All data in the private region is duplicated for extra reliability.

A region of a physical disk managed by VxVM that contains available space and is used for allocating subdisks.

A Redundant Array of Independent Disks (RAID) is a disk array set up with part of the combined storage capacity used for storing duplicate information about the data stored in that array. This makes it possible to regenerate the data if a disk failure occurs.

A recovery mode in which each read operation recovers plex consistency for the region covered by the read. Plex consistency is recovered by reading data from blocks of one plex and writing the data to all other writable plexes.

The configuration database for the root disk group. This is special in that it always contains records for other disk groups, which are used for backup purposes only. It also contains disk records that define all disk devices on the system.

The disk containing the root file system. This disk may be under VxVM control.

A special private disk group that always exists on the system. The root disk group is named rootdg. Even though rootdg is the default disk group, it does not necessarily contain the root disk unless this is under VxVM control.

The initial file system mounted as part of the UNIX kernel startup sequence.

The disk region on which the root file system resides.

The VxVM volume that contains the root file system, if such a volume is designated by the system configuration.

The ability to place the root file system and the swap device under VxVM control. The resulting volumes can then be mirrored to provide redundancy and allow recovery in the event of disk failure.

In active/passive disk arrays, the paths to a disk other than the primary path are called secondary paths. A disk is supposed to be accessed only through the primary path until it fails, after which ownership of the disk is transferred to one of the secondary paths. Also see path and primary path.

A unit of size, which can vary between systems. Sector size is set per device (hard drive, CD-ROM, and so on). Although all devices within a system are usually configured to the same sector size for interoperability, this is not always the case. A sector is commonly 1024 bytes.

A disk group in which access to the disks is shared by multiple hosts (also referred to as a cluster-shareable disk group). Also see private disk group.

A VM disk that belongs to a shared disk group in a cluster.

A volume that belongs to a shared disk group and is open on more than one node of a cluster at the same time.

A node that is not designated as the master node of a cluster.

The standard division of a logical disk device. The terms partition and slice are sometimes used synonymously.

A layout technique that permits a volume (and its file system or database) that is too large to fit on a single disk to be configured across multiple physical disks.

A plex that is not as long as the volume or that has holes (regions of the plex that do not have a backing subdisk).

A networking paradigm that provides easily reconfigurable connectivity between any subset of computers, disk storage and interconnecting hardware such as switches, hubs and bridges.

A set of stripe units that occupy the same positions across a series of columns.

The sum of the stripe unit sizes comprising a single stripe across all columns being striped.

Equally-sized areas that are allocated alternately on the subdisks (within columns) of each striped plex. In an array, this is a set of logically contiguous blocks that exist on each disk before allocations are made from the next disk in the array. A stripe unit may also be referred to as a stripe element.

The size of each stripe unit. The default stripe unit size is 32 sectors (16K). A stripe unit size has also historically been referred to as a stripe width.

A layout technique that spreads data across several physical disks using stripes. The data is allocated alternately to the stripes within the subdisks of each plex.

A consecutive set of contiguous disk blocks that form a logical disk segment. Subdisks can be associated with plexes to form volumes.

A disk region used to hold copies of memory pages swapped out by the system pager process.

A VxVM volume that is configured for use as a swap area.

A set of configuration changes that succeed or fail as a group, rather than individually. Transactions are used internally to maintain consistent configurations.

A disk that is both under VxVM control and assigned to a disk group. VM disks are sometimes referred to as VxVM disks or simply disks.

A small file that is used to locate copies of the rootdg (root disk group) configuration. The file may list disks that contain configuration copies in standard locations, and can also contain direct pointers to configuration copy locations. A rootdg that contains only simple disks requires entries for at least some of those disks in the volboot file so that vxconfigd can configure the disk group. The volboot file is stored in a system-dependent location.

A virtual disk, representing an addressable range of disk blocks used by applications such as file systems or databases. A volume is a collection of from one to 32 plexes.

The volume configuration device (/dev/vx/config) is the interface through which all configuration changes to the volume device driver are performed.

The driver that forms the virtual disk drive between the application and the physical device driver level. The volume device driver is accessed through a virtual disk device node whose character device nodes appear in /dev/vx/rdsk, and whose block device nodes appear in /dev/vx/dsk.

The device interface (/dev/vx/event) through which volume driver events are reported to utilities.

The VxVM configuration daemon, which is responsible for making changes to the VxVM configuration. This daemon must be running before VxVM operations can be performed.