Determine what type of cabinet you are installing
the slide-tray assembly into.
E-Series cabinets have:
Parchment white, plastic, sectional,
side panels
Black painted vertical frame posts with a partial
return flange
Approved, non-E-Series, cabinets have:
Single piece metal side panels
Gray painted vertical frame posts with full return
flanges
Note the vertical, rectangular, slots in the return
flanges on the vertical mounting posts. Determine into which of
these vertical slots the slide/tray kit will be installed. This
is done by counting down eight rectangular slots from the top of
the cabinet or the bottom of the equipment above.
On the front vertical mounting posts only, slide M5 sheet metal nuts onto
the posts over the holes immediately adjacent to the vertical slots
determined in the previous step. Also place M5 sheet metal nuts
on the holes directly above these. Orient the sheet metal nuts so
that the threaded portion faces towards the outside of the cabinet.
There should now be a total of four (4) sheet metal nuts installed.
If the cabinet is a non-E-Series cabinet, discard the
left hand and right hand aluminum spacers and two of the M5 x 16
screws with cress-cup washers and proceed to step 12.
If the cabinet is an E-Series cabinet, place the hook
of the aluminum spacer marked “L” (5183-1864) into
the appropriate vertical, rectangular slot on the front, left hand
mounting post. The hook points downward. Similarly, place the spacer
marked “R” (5183-1863) into the appropriate slot
on the right hand mounting post.
Use one M5 x 16 screw with cress-cup washer to attach
each spacer to its vertical post. Do this by inserting the screw
through the top hole in the spacer, through the mounting rail and
tightening it into the sheet metal nut located at that position.
Take the left hand slide/bracket assembly (marked 337079-1L)
and install it into the left hand vertical mounting posts. This
is done by inserting the pin at the rear of the slide's mounting
bracket into the 23rd hole in the rear vertical mounting post and
inserting the hook at the front of the bracket into the vertical,
rectangular slot in the aluminum spacer. The slide should be positioned
in the cabinet so that it is horizontal and level.
Securely fasten the rear of the slide's mounting bracket
to the rear vertical mounting post by installing and tightening
two of the M5 x 16 screws with cress-cup washers thorough the mounting post,
through the slides mounting bracket and into the threaded nuts attached
to the mounting bracket.
Fully extend the slide so that it is locked in the fully
open position.
Use an M5 x 30 screw with a cress cup washer to attach
the front of the slide to the vertical mounting post. Insert the
screw through the slide, through the center hole of the aluminum
spacer, through the vertical mounting post, and tighten into the
sheet metal nut located at that position.
Use a procedure similar to steps 7 through 10 to install
the right hand slide/bracket assembly (marked 337079-1R) and then
proceed to step 12.
Take the tray and place it onto the pins that extend
from the slides' inner members. The slots with wide lead-in guides
on the side of the tray fit down onto the slides' pins. The flat
part of the tray will be on top, and the mounting holes in the top
of the tray will be located to the right of the center of the tray.
Slide the tray all the way down on both sides so that the pins reach
the top of the slots in the side of the tray.
Use six, M5 x 12 screws (without washers) to attach
the tray to the slides. Three screws are used to attach each slide.
Insert the screws through the slides, through the tray and tighten
into the threaded nuts located on the inside of the sides of the
tray.
From the bottom of the tray pull the plunger pin down
and give it a 1/4 turn to hold it in place.
Position the server on the tray aligning the plunger
pins with the alignment holes in the chassis.
Release the plunger pins to secure the server.
Printable version
