Compatibility Information and Installation Requirements

This section describes the requirements for installing version I.11.00.80 of the ATM link software on HP-UX 11.0.

OS Platform and Version Compatibility

You must have already installed HP-UX 11.0 before you install the ATM software.

Software Requirements

The various software requirements for this release of ATM are described in the subsections below.

HP-UX Operating System Patch Dependencies

Table 2-2 “ATM HP-UX 11.0 Operating System Patch Dependencies” below lists the HP-UX 11.0 Operating System patches that ATM has dependencies on. Please note that only some of the patches are required, but we strongly recommend that you also install the other patches listed.

Table 2-2 ATM HP-UX 11.0 Operating System Patch Dependencies

HP 9000 System	Required/ Recommended	32-Bit/ 64-Bit	Patch Number	Description
Servers & workstations	Required	32 & 64	`PHKL_18543` (also in HP-UX 11.0 ACE 9911)	WSIO CDIO, shared interrupts, and 16-cycle timeout
	Recommended	32 & 64	`PHNE_20008`	STREAMS
	Recommended	32 & 64	`PHNE_20436`	ARPA Transport

Contact your Hewlett-Packard representative to install the patch that is appropriate for your HP 9000 system.

High Availability Requirements

To use the High Availability feature for remote recovery, version A.10.10 of the MC/ServiceGuard software must be installed on all cluster systems running the software.

V-Class Firmware Requirements

For this release of ATM, the A5483A, A5513A, and A5515A HP-PCI adapters require the following V-Class system firmware versions:

For Model V22 xx: Test Station software version 5.0.
For Model V2500: Test Station software version 1.1.

Hardware Requirements

You must have an appropriate ATM adapter installed in your HP 9000 system. You can combine adapters, as long as they are all supported for your system. Table 2-3 “HP-UX 11.0 Supported ATM Adapter Configurations” below lists the supported adapter configurations for HP-UX 11.0. Note that discontinued adapters are not shown.




	WARNING! For T600 and V-Class servers, the ATM adapters must be installed by qualified Hewlett-Packard personnel. On all of the other models of HP 9000 systems shown in Table 3-3 below, the ATM adapters are customer installable.

Table 2-3 HP-UX 11.0 Supported ATM Adapter Configurations

Bus Type	HP 9000 System	ATM Adapter	Maximum Adapters per System	Maximum VCs per Adapter	Maximum VCs per System
HP-HSC 155	K570/580 and T600 servers	J2469A	6	2048	6144
	K-Class servers (other than K570/580)	J2469A	4	2048	6144
	R380/390 servers and B-, C-, and J-Class workstations	J2499A	4	2048	6144
	D-Class servers	J2499A	4	2048	6144
	74x industrial workstations	J3420B	4	2048	6144
HP-HSC 622	D-Class servers	J3573A	1	4096	6144
HP-HSC 622	R380/390 servers	J3573A	2	4096	6144
HP-PCI 155	V-Class servers	A5513A	16	2048	6144
	V-Class servers	A5515A	16	2048	6144
	L-Class and N-Class servers	A5513A	16	2048	6144
	L-Class and N-Class servers	A5515A	16	2048	6144
	B1000, C3000, J5000, and J7000 workstations	A5513A	4	2048	6144
	B1000, C3000, J5000, and J7000 workstations	A5515A	4	2048	6144
HP-PCI 622	V-Class servers	A5483A	8	4096	6144
	L-Class and N-Class servers	A5483A	16	4096	6144
	B1000, C3000, J5000, and J7000 workstations	A5483A	4	4096	6144

Important: Listed below are some things you should keep in mind when using the information shown in the table above:

The "Maximum Adapters per System" column shows the maximum number of ATM adapters the ATM software can support for each class of HP 9000 system. However, keep in mind that some models within a class might have fewer physical slots available for ATM adapters than the number shown in the "Max. Adapters per System" column. Increasing the number of adapters lets you increase the number of VCs (see “Disk Space and Memory Requirements” for memory-related limitations). The effective bandwidth will depend mostly on the number and type of HP 9000 systems.

The "Maximum VCs per Adapter" also depends on the HP 9000's available RAM at system boot time—the driver checks the amount and limits the number of available VCs accordingly. Table 2-4 “Maximum VCs per Adapter Based on Available RAM” below shows, for each affected adapter, the amount of available RAM and the corresponding VC limit. Note that discontinued adapters are not shown.

Table 2-4 Maximum VCs per Adapter Based on Available RAM

HP ATM/155 Adapters (A5513A, A5515A, J2469A, J2499A, and J3420B)		HP ATM/622 Adapters (A5483A and J3573A)
Available RAM	Maximum VCs per Adapter	Available RAM	Maximum VCs per Adapter
Less than or equal to 32 MBytes	256	Less than or equal to 32 MBytes	256
Less than or equal to 64 MBytes	512	Less than or equal to 64 MBytes	512
Less than or equal to 128 MBytes	1024	Less than or equal to 128 MBytes	1024
Greater than 128 MBytes	2048	Less than or equal to 256 MBytes	2048
n/a	n/a	Greater than 256 MBytes	4096

You also can use the atmmgr show -c command to display the maximum number of VCs (called "VCCs" in the command's output) for an adapter.

Disk Space and Memory Requirements

The disk space and memory requirements are shown below (discontinued adapters are not shown).

HP-HSC bus.
- Disk space required to install: 13 MBytes.
- Disk space required to run: None.
- Memory space required: Table 2-5 “ Memory Requirements for Maximum Configured VCs—HP-HSC” below shows the amount of memory that is required if the maximum number of VCs are configured on each type of ATM adapter. Note that systems with less memory available can support fewer VCs. Also, other drivers present in the system share the memory resources, which might reduce the total number of VCs that can be opened.
  Table 2-5 Memory Requirements for Maximum Configured VCs—HP-HSC
  ATM Adapter
  Max. VCs Open Simultaneously
  Memory Required (in MBytes)
  J2469A and J2499A
  2048
  256
  J3420B
  2048
  256
  J3573A
  4096
  512
- Swap space required: Not specified.
HP-PCI bus.
- Disk space required to install: 12 MBytes.
- Disk space required to run: None.
- Memory space required: Minimal.
- Swap space required: Not specified.

System State at Installation

To install the ATM adapter, you must turn the system's power off. After you install the ATM adapter, turn the system's power on. Then, install the ATM software (the system is automatically rebooted as part of the installation process).

Software Installation Instructions

See the ATM Configuration and Troubleshooting Guide (p/n B1056-90007) for detailed information about installing the ATM link software.

Estimated time to install: 30 minutes (this includes hardware and software installation).

Known Compatibility or Incompatibility with Third-Party Products

The ATM software products operate with all UNI 3.0-, UNI 3.1-, and UNI 4.0-compliant ATM switches and equipment that comply with LAN Emulation over ATM versions 1.0 and 2.0 and MPOA version 1.0.