Jump to content United States-English
HP.com Home Products and Services Support and Drivers Solutions How to Buy
» Contact HP
More options
HP.com home
 HP A7173A PCI-X Dual Channel Ultra320 SCSI Host Bus Adapter Support Guide: HP-UX 11i v1, 11i v2, and 11i v3 > Chapter 2 Installing the A7173A Adapter

Installing A7173A Adapter Hardware
» 

Technical documentation

Complete book in PDF
» Feedback
Content starts here

 » Table of Contents

 » Glossary

 » Index

spacerspacerspacer
spacer
spacer
  		 
 

This section contains information about installing the A7173A adapter hardware in a supported HP-UX system.

WARNING! The installation procedures in this section require opening the computer cabinet, which might expose you to high-energy (high-amperage) circuits and sharp edges on the equipment chassis. Be sure to remove all rings, watches, and other jewelry before opening the cabinet.

Before beginning installation, and without removing the adapter from its antistatic bag, inspect the adapter for any signs of obvious damage, such as chipped or loose components. Contact HP if the adapter is damaged.

CAUTION: The A7173A adapter contains electronic components that can easily be damaged by small amounts of static electricity. To avoid damage, follow these guidelines:

  • Store the adapter in its antistatic plastic bag until you are ready to install it.

  • Work in a static-free area, if possible.

  • Handle the adapter by the edges only. Do not touch electronic components or electrical traces.

  • If you must lay the adapter down, place it on a non-conductive mat or surface.

  • Use the Electrostatic Discharge (ESD) kit that is provided with the adapter. Follow the instructions included with the kit.

  • Use a suitable ground; for example, an exposed metal surface on the system chassis can serve as a ground.

Offline Installation

Install the A7173A adapter in any supported HP-UX system according to the offline host bus adapter installation procedure for that system. For more information about installation procedures, see the HP system documentation at:

http://docs.hp.com/en/hw.html

NOTE: The A7173A adapter can be installed in any PCI or PCI-X slot, but for best performance, HP recommends installing the adapter in a PCI-X, 133 MHz, 64 bit, 4x (“Twin Turbo” or “Dual Rope”) slot. For more information on slot specifications, see the system documentation; or, for entry-class servers, see the I/O Slot Matrix – Entry Class Integrity Servers, at:

http://docs.hp.com/en/hw.html#General%20Guides

After installing the A7173A adapter, go to “Connecting SCSI Peripheral Devices”.

Online Installation

The Online Addition and Replacement feature (OLAR for HP-UX 11i v1, or OL* for HP-UX 11i v2 and later HP-UX releases) enables you to add or replace PCI host bus adapters without shutting down and rebooting the system, and without adversely affecting other system components. The system hardware uses slot-specific power control, combined with HP-UX operating system support, to enable these features.

For more information on OLAR or OL*, see the following documents:

IMPORTANT: Superdome systems are not intended for access by users. HP recommends that Superdome systems only be opened by a qualified HP engineer. Failure to observe this requirement can invalidate any support agreement or warranty to which the system owner might otherwise be entitled.If you use OLAR or OL* to add or replace an A7173A adapter, the SCSI ID will be set at 7 by default. If the SCSI ID for an add-in or replacement adapter needs to be set at some value other than 7, the mptconfig command can be used to set the SCSI ID after the A7173A adapter is inserted into the slot and powered on, but before the SCSI cable(s) are connected. See “About SCSI IDs” and “Using mptconfig for Online Configuration”, for more information.


System Firmware
  		 


Connecting SCSI Peripheral Devices  
Printable version
Privacy statement Using this site means you accept its terms Feedback to webmaster
© 2007 Hewlett-Packard Development Company, L.P.