EMS Hardware Monitors (logo)

Release Notes for EMS Hardware Monitors on HP-UX 11i v1 (11.11) (June 2009)

Online Diagnostics

The Online Diagnostics software is a collection of tools that enables you to monitor and test server hardware. It comprises the Event Monitoring Service (EMS) framework, the EMS Hardware Monitors, and the Support Tools Manager (STM).

The Online Diagnostics tools are all contained in a Software Depot (SD) bundle, called the OnlineDiag bundle. This bundle is distributed in the following ways:

The following generic command lists various levels of content of the depot:

swlist -l <level> -s /<mount_point>/DIAGNOSTICS/<os_release>

where <level> 
         = bundle       Bundle level listing
         = product      Product level listing
         = subproduct   Sub-product level listing
         = fileset      File set listing

      <mount_point>     Location where the CD file system
                        is mounted.

      <os_release>      The OS contents of the depot.
         = B.11.00

For OnlineDiag on HP-UX 11i v1 June 2009 release, the following apply:

Pre-requisites

Following is the software pre-requisite for  installing Diagnostics and Support Tools:

  • EMS version A.04.20.11 or later

    • Note: The requirements are available on the Operating Environment (OE) media.

    Required and Recommended Patches

    The patch bundles are available at the following locations:

    Loading Patches

    You can install the patches in one of the following ways:

    Method 1:
    Install the entire Hardware Enablement Bundle (HWE) or Quality Pack (QPK) patch bundle for your system. This is a simple and tested process. However, the volume of the patch bundle can be big.

    Method 2:
    Install only the individual patches required from the patch bundle available on the OE media. This method is advantageous because the size of the patches is small. However, you must select and install patches manually.

    Method 3:
    Install individual patches from the HP IT Resource Center at:
    http://us.itrc.hp.com/

    Notes:

    EMS Hardware Monitors Overview

    EMS Hardware Monitors are a set of tools for maintaining system availability. They enable you to monitor the operation of a wide variety of hardware resources and be alerted immediately if any failure or other unusual event occurs.

    Hardware event monitoring provides a high level of protection against system hardware failure. By using hardware event monitoring, you can eliminate the most undetected hardware failures that could interrupt system operation or cause data loss.

    Note: On the HP-UX 11i v1 operating system, Online Diagnostics does not support tape drives. Although some of the Support Tools Manager (STM) tools may work with tape drives, they are not supported. The diagnostic tools and utilities that support these devices are HP StorageWorks Library and Tape Tools (L and TT). These tools are available at:
    http://www.hp.com/support/tapetools

    Configuring Hardware Monitoring

    The EMS Hardware Monitors are installed at the same time as STM. Once the monitoring software is installed, monitoring is automatically enabled.

    By default, events with severity levels MAJOR WARNING, MINOR WARNING, SERIOUS, or CRITICAL that are generated by the monitors are notified in the following ways:

    All events generated by all the monitors are stored in the /var/opt/resmon/log/event.log file.

    To configure, enable, or disable hardware event monitoring, run the /etc/opt/resmon/lbin/monconfig monitoring request manager.

    The Peripheral Status Monitor (PSM) and the Kernel Resource Monitor (krmond) are configured differently. They use the EMS GUI. For more information, see:
    http://docs.hp.com/en/diag/ems/ems_gui.htm

    Changes

    Changes made to the EMS Hardware Monitors for the June 2009 release include the following:

    Known Problems

    Monitors Provided

    For HP-UX 11i v1 June 2009 release, the following monitors are provided:

    For detailed information about the products and the monitors supporting them, and additional dependencies, see the Online Diagnostics Administrator's and User's Guide at:
    http://docs.hp.com/en/diag/

    Product Documentation

    For the latest and most complete information on EMS Hardware Monitors and the STM, see the documentation of Online Diagnostics at:
    http://docs.hp.com/en/diag/

    SD Product Structure

    Following are the components of the OnlineDiag bundle:

    SD Bundle: OnlineDiag
   Description: On-line Diagnostic System (Series 800/700)

   SD PRODUCT: Sup-Tool-Mgr
      Description: Support Tools Manager for HP-UX Systems

      SD SUB-PRODUCT: Manuals
      Description: Support Tools Manager Manual Pages

         FILESET: RELEASE_NOTES
            Description: HPUX STM Release Notes

         FILESET: STM-MAN
            Description: HPUX STM Manual Pages

      SD SUB-PRODUCT: Runtime
      Description: STM Manual Runtime

         FILESET: STM-CATALOGS
            Description: HPUX STM Shared Libraries

         FILESET: STM-SHLIBS
            Description: HPUX STM Shared Libraries

         FILESET: STM-UI-RUN 
            Description: HPUX STM User Interface
         
         FILESET: STM-UUT-RUN
            Description: HPUX STM Unit Under Test Runtime

    Reporting Defects

    You can report defects and send suggestions to diag.onlinediag.docs using QUIX. If you do not have access to QUIX, contact your local HP representative to file a defect on your behalf.

    Top of Page / Diagnostics HOME
    URL: http://docs.hp.com/en/diag/ems/emr_0906_1111.htm
    Last updated: Tuesday, May 26, 2009